Party Candy Dispenser
Description
A Big Single Candy Fountain!
Made with FOOD SAFE materials.
Suggestion
1 Large Bag of Candy
Ideal for smooth shell and small candies
Caution
Allergen: Contains Latex Rubber Bands
Wrapper is a suffocation hazard. Small parts are a choking hazard. Avoid paper cuts and poking the sharp corners.
Buy as a Sheet for $1.25
Basically pluck out, fold, and assemble. Decorate optional. No glue nor tape required.
Not Included
Candy, physical decor, nor mini-cups
User Submitted Images
Decor Download
IDEAL TO USE THE STEP-BY-STEP INSTRUCTIONS INSTEAD OF ASSEMBLY VIDEO
ASSEMBLY: SEE STEP-BY-STEP BELOW
Complete video for step-by-step assembly. See below for easier step-by-step instructions.
Attention!
Step 1
Cardboard bends easily. It is best to bend at the bend lines. Follow the instructions for best results.
Step 2
Remove the wrapper from the edge without lifting the cardboard.
Step 3
Remove the window and rubber band package.
Step 4
With 1 hand under the cardboard using fingers, press up while using the other hand or thumb to hold the top portion of the cardboard in place or press down. Always remove alongside the edges. Avoid lifting the cardboard too high.
Step 5
Remove the small rectangles. See yellow image to know where.
Step 6
Bend at the 7 bend lines as shown.
Step 7
Bend at the 4 bend lines as shown.
Step 8
Bend at the 3 bend lines as shown. To make a tight corner, pinch edge as shown while lifting the cardboard in the air.
Step 9
Bend at the 3 bend lines as shown.
Step 10
Bend at the bend line as shown. To make a tight edge, pinch the edge while holding cardboard in the air as shown.
Step 11
Bend at the 8 bend lines as shown.
Step 12
Bend at the 2 bend lines as shown.
Step 13
Fold and position as shown.
Step 14
Fold wrap with tabs in 2 slots.
Step 15
Fold and position as shown.
Step 16
Hold in the 3 tabs and insert into the back while folding in the back. Position as shown.
Step 17
Fold the wrap until the two tabs are in the slots.
Step 18
Fold and position as shown.
Step 19
Fold and position tab as shown.
Step 20
Use the one that has wavey holes on top. Fold as shown.
Step 21
Carefully press this edge to prevent sawing of rubber band. Use your finger, nail, or a rod like tool.
Step 22
Carefully press this edge to prevent sawing of rubber band. Use your thumb or a rod like tool.
Step 23
Carefully press this edge to prevent sawing of rubber band. Use finger, nail, or a rod like tool.
Step 24
Fold pusher, stretch rubber band, and place rubber band on pusher as shown.
Step 25
Place pusher on base and push so the button goes through the hole.
Step 26
Hold rubber band at the bottom while straightening rubber band at top as shown.
Step 27
Insert at an angle as shown.
Step 28
Press until no large gaps. May need to swivel pusher while pressing down.
Step 29
Pull and position rubber band as shown. Make sure it don’t rub against the pusher button.
Step 30
Push a few times to smooth pusher and then it should smoothly close. If not, check for gaps. If no gaps, re-tighten the rubber band.
Step 31
Slide in window. Pull apart the bottom window frame and gently slide the window further in.
Step 32
Fold left tab, then middle, then right tab. Then bend wall divider and insert into 2 slots as shown. The wall divider is optional if less candy is used to help make it look fuller.
Step 33
Fold the tab and insert into slot.
Step 34
Congratulations. You now have your very own party candy dispenser! Fill it up and have fun!