Candy Fountain


Instead of a soda fountain, what about a CANDY FOUNTAIN! Enjoy 5 different candies filling up your little cup!
Made with FOOD SAFE materials. 


5 Theater Candy Boxes
Ideal for smooth shell and small candies


Allergen: Contains Latex Rubber Bands 
Wrapper is a suffocation hazard. Small parts are a choking hazard. Avoid paper cuts and poking the sharp corners. 

Buy as a Sheet for $1

Basically pluck out, fold, and assemble. Decorate optional. No glue nor tape required. 

User Submitted Images

Decor Download


This assembly video shows how to build the Candy Fountain from start to finish using the EASY but NOT SUGGESTED rubber band assembly method which MAY CAUSE ISSUES. See STEP M1. 
To proceed with the CHALLENGING but RECOMMENDED rubber band assembly method, see STEP M2.

Avoid Damage

Step 1

Cardboard bends. Avoid damage by following instructions. Pluck/punch out parts along edge. Bend at bend lines. The less damage, the better it performs. Some people may find it helpful with the use of a rod like tool for bending, plucking, and edge crushing. Up to you.

Step 2

Carefully rip the wrapper edge while cardboard is on flat surface. Remove wrapper without lifting cardboard. 

Step 3

Remove the rubber bands and place to the side for now.

Step 4

Remove the window and remove its tape. Place to the the side for now.

Step 5

Extract/pluck/punch the cardboard from bottom up without lifting much of the sheet of cardboard. Do this by tracing the inside edge of the part under the cardboard with fingers while the other hand is on the outside edge of the part pushing down. Gently remove part once trace is complete. Place parts to the side when they are ready. Discard sheet after all parts are removed.

Step 6

Remove the small rectangles. Because these are small, you can extract how you want – in or out. Feel free to use a tool of some sort to push them out. See the image with yellow highlights to see the pieces to remove.

Step 7

Bend the ramps at bend lines. 

Step 8

Bend the pushers/button. Pinch tip as shown to help slide through slot.  

Step 9

Bend at bend lines. 3 Bend lines here.

Step 10

Bend at bend lines. 3 Bend lines here. The 3rd bend line is dashed. Reverse bend the dashed line. 

Step 11

Bend at bend line.

Step 12

Bend at double bend lines. Press edge of bend line to tighten bend. Bend close to edge. 

Step 13

Bend at at bend lines. 2 bend lines here. 1st was reverse bend. 2nd bend line, try to bend close to edge.

Step 14

Bend at at bend lines. 4 bend lines here. Bend close to edge as possible for 4th bend line. 

Step 15

Bend at at bend lines. 4 bend lines here. Bend close to edge as possible. The 4th bend line, press edge when bending to make bend a right angle easily. 

Step 16

Bend at at bend lines. 2 bend lines here. The 2nd bend line requires bending mid-air. Make sure the part is off the surface when bending. 

Step 17

Bend at at bend line. Do this mid-air. Then pinch edge. Then pinch edge of other side mid-air. 

Step 18

Insert window with the U slots aligned with the slots as shown. 

Step 19

Follow per instructions. 

Step 20

Follow per instructions. Notice how the part hold is held. Lift part in air as shown. Thumb in edge while holding back wall, pushing toward thumb where slots are. Move thumb in the other alike edges while pressing back so the gap is flushed to wall as shown.

Step 21

Wrap around as shown and click in the two tabs. Press edge down to press two tabs into slots further if necessary. 

Step 22

Wrap around as shown and click in the tab. Press edge down to press two tabs into slot further if necessary. 

Step 23

Fold as shown. 

Step 24

Fold as shown. 

Step 25

Slide the window up to the top and aligned with the U slots. If the window won’t slide up, then pull apart the top window frame a little. 

Step 26

Align the hooks to the right side and pinch bottom tip tab to help insert. Gently squeeze to help hook slide into slot. Make sure bottom tab enters base slot. 

Step 27

Choose your Rubber Band Assembly Method:
M1: Easy but May Cause Issues (Go to Step M1:1)
M2: Recommended (Go to Step M2:1)

Step M1:1

With your thumb or a rod tool, crush the top corner base edge shown. Doing so will help prevent the rubber band from being cut by the edge of the cardboard via scrape like action. 

Step M1:2

Stretch a rubber band. Slightly open the pusher/button as shown. Then add the rubber band as shown. Hold the rubber band.

Step M1:3

Insert with the rubber band hanging into the hole. With other hand, latch on the rubber band and gently pull. Then let pusher flush with base and move pusher around until the button slides through hole with support of pulling the rubber band gently and finger to push through hole from the back. 

Step M1:4

Slide the rubber band into the two slits. The 3rd GIF shows how to place the rubber band on the tab for the 4 other rubber bands. 

Step M1:5

Insert the ramp at an angle. Then push ramp legs down to flush with base. Wiggle the button pusher to allow ramp legs to fit between wall and the button pusher. 

Step M1:6

Reduce the friction by smoothing the cardboard. Push the button slider a few times and pull if needed. If that isn’t helping close, make sure the ramp legs are flushed to the base between the wall and button pusher. If it is, then tighten the rubber band some more. 
If it is jammed and all else was tried, then take ramp out and pinch the legs. 

Step M1:7

Bend tabs and close lid. Congratulations! You now have your very own Candy Fountain! Decorate it and fill it with candies! Have a blast!

Step M2:1

With your finger, thumb, or a rod like tool, press the top right surface down to slightly crush the edge to help stop a saw like motion that could cut the rubber band. 

Step M2:2

With your fingernail or a tool, press the left edge of the small cut so the right edge of the small cut is exposed. 

Step M2:3

Place the rubber band on the pusher as shown. Let the rubber band hang through the hole ase you line up the button with the slot. Grab the rubber band hoop from the bottom with the other hand. Let the slider on the base and help push it so the button goes through the hole while holding the rubber band hoop with the other hand. 

Step M2:4

Using your finger, push the hoop up through the next hole while grabbing it with the other hand. Then place the hoop over the tab. Push in rubber band to fall into tab slot. 

Step M2:5

Lift rubber band and slide it through the large cut. Then place the rubber band to the right edge of the small cut.  
Repeat Step M2:3, M2:4, & M2:5 for the next 3 sliders. 

Step M2:6

Lift rubber band and place it to the right edge of the small cut, around the button, and hook the rubber band into the slot at the corner as shown.   

Step M2:7

Wedge the rubber band behind the cut as shown. This is just to keep the rubber band off the button.   

Step M2:8

Pinch the right edge portion of the ramp. Repeat for all 5 ramps. Place ramp in at angle and then flush the legs to the base between the slider and wall. Wiggle the button to help the ramp fit. Do this for the remainder of the ramps. 

Step M2:9

Smooth the button by pushing a few times via saw like motion to the left and right edge. If button still won’t come back, proceed to Step M2:10. 

Step M2:10

If the button comes back out a little, then you might want to tighten the rubber band. If your rubber band is not at the end like this one, pull off the rubber band from the big cut. Then pull out from the small cut and then wedge into big cut. Or just retighten the whole thing again by repeating Step M2:3, M2:4, & M2:5. Got to Step M2:11 if button still won’t come out. 

Step M2:11

If the button don’t come out, take ramp out and pinch its legs (both sides completely). Place back in. 

Step M2:12

Close the lid while keeping the two tabs in. 
Congratulations! Fill it up and enjoy your own Candy Fountain!